Skip to content

Flashing Matek R24

Setup-Banner

Flashing via Wifi

Target: MATEK_2400_RX_via_WIFI

Wire up your receiver to a free UART on your Flight Controller. Wire TX on receiver to an RX pad on the FC, and the RX on receiver to a TX pad on the FC in the same UART. Wire 5v and Gnd as normal (5v to a 5v pad on FC and Gnd to a Gnd pad on the FC).

Note: There are Flight Controllers that will pull the RX pads LOW which will put the ESP-based receivers into Bootloader Mode unintentionally. A solid LED light on these receivers even with the TX module off is a sign they are in Bootloader Mode. If this is the case, rewire the receiver to a different UART.

Build the firmware using the ExpressLRS Configurator using the correct Target and options. Once done, it should open a new window where the MATEK_2400_RX-<version>.bin is. Do not close this window so you can easily navigate to it once it's time to upload the firmware into the receiver.

Power your Flight Controller by either connecting a LiPo or attaching the USB cable (if receiver gets powered from USB via a 4v5 pad). Receiver's LED will blink slow at first, and after 20s or 30s (can be adjusted via ExpressLRS Configurator using AUTO_WIFI_ON_INTERVAL), it should blink fast indicating it's on Wifi Hotspot Mode.

Connect to the Wifi Network the receiver has created. It should be named something like ExpressLRS RX with the same expresslrs password as the TX Module Hotspot. Navigate to the same web address as the TX Module (usually http://10.0.0.1). The Firmware upload page should load, and using the File Upload Form, navigate where the correct Receiver MATEK_2400_RX-<version>.bin is (you can drag-and-drop the firmware file into the form field or use the Browse or Choose File button). Click on Update button and the firmware file will be uploaded and the update process should commence.

A white page should load momentarily with the message Update Success! Rebooting.... Wait a little bit (you can wait until the LED on the Receiver starts to blink slowly again) and the receiver should be updated. Power cycle and your module and receiver should now be bound (given you have updated the Tx Module as well, and that they have the same binding phrase and options).

Flashing via Passthrough

Target: MATEK_2400_RX_via_BetaflightPassthrough

Wire up your receiver to a free uart in your Flight Controller. Wire TX on receiver to an RX pad on the FC, and the RX on receiver to a TX pad on the FC in the same UART. Wire 5v and Gnd as normal (5v to a 5v pad on FC and Gnd to a Gnd pad on the FC).

Power your FC with a LiPo, or if receiver is powered via USB (receiver is connected to a 4v5 pad), connect the FC to your USB port.

Note: if the receiver has solid LED light but is not bound to your module, your FC is probably pulling the current UART's RX pad LOW which will interfere with the normal and passthrough flashing of this receiver. Find another UART and wire your receiver there instead.

Using the ExpressLRS Configurator, with the correct Target selected and Firmware Options set, click on Build & Flash. Wait for the process to finish and you should be greeted with the "Success" banner.

Unplug USB and/or LiPo. Power your TX Module and then your FC to verify you are bound and has connection.

Flashing via UART

Target: MATEK_2400_RX_via_UART

Wire the receiver into the FTDI, with TX on receiver connected to the Rx on the FTDI, and RX on receiver connected to the Tx of the FTDI. Wire 5V and GND of the FTDI to 5V and GND of the Receiver. Press the button while powering the RX on, and release - the LED should now be solid.

Select the target and set your Firmware Options and once done, click on Build and Flash.